Vorschläge für neue I/O-Signale: Unterschied zwischen den Versionen
Rsc (Diskussion | Beiträge) (Neue "Sub Function Codes" für den "Basic Function Code" 0x0E) |
K (WikiSysop verschob die Seite Neue I/O-Signale nach Vorschläge für neue I/O-Signale) |
||
(39 dazwischenliegende Versionen von 6 Benutzern werden nicht angezeigt) | |||
Zeile 1: | Zeile 1: | ||
Hier erfolgt eine Auflistung von Signalen der virtuellen Ein- und Ausgänge zur Ergänzung des Standards | Hier erfolgt eine Auflistung von Signalen der virtuellen Ein- und Ausgänge, die als Vorschläge zur Ergänzung des Standards CiA-417 erarbeitet werden. | ||
= Eingänge = | = Eingänge = | ||
== | == Inspektionssteuerung (Basic function 0x13, Inspection mode) == | ||
{|border="1" cellspacing="" cellpadding="3" | {|border="1" cellspacing="" cellpadding="3" | ||
Zeile 12: | Zeile 11: | ||
!Bemerkung | !Bemerkung | ||
|- | |- | ||
| | | 0x00 || Reserved || | ||
|- | |- | ||
| | | 0x01 || Inspection on || | ||
|- | |- | ||
| | | 0x02 || Inspection up || | ||
|- | |- | ||
| | | 0x03 || Inspection down || | ||
|- | |- | ||
| | | 0x04 || Inspection fast || | ||
|- | |- | ||
| | | 0x05 || Inspection shaft pit on || | ||
|- | |- | ||
| | | 0x06 || Inspection shaft pit up || | ||
|- | |||
| 0x07 || Inspection shaft pit down || | |||
|- | |||
| 0x08 || Inspection shaft pit fast || | |||
|- | |- | ||
|} | |} | ||
== Rückholsteuerung (Basic function 0x14, Emergency recall operation) == | |||
== | |||
{|border="1" cellspacing="" cellpadding="3" | {|border="1" cellspacing="" cellpadding="3" | ||
Zeile 38: | Zeile 40: | ||
!Bemerkung | !Bemerkung | ||
|- | |- | ||
| 0x00 || Reserved | | 0x00 || Reserved || | ||
|- | |- | ||
| 0x01 || | | 0x01 || Emergency recall operation on || | ||
|- | |- | ||
| 0x02 || | | 0x02 || Emergency recall operation up || | ||
|- | |- | ||
| | | 0x03 || Emergency recall operation down || | ||
|- | |- | ||
|} | |} | ||
== | == Kopierwerk/Magnetschalter (Basic function 0x15, Shaft copy) == | ||
{|border="1" cellspacing="" cellpadding="3" | {|border="1" cellspacing="" cellpadding="3" | ||
Zeile 59: | Zeile 59: | ||
!Bemerkung | !Bemerkung | ||
|- | |- | ||
| 0x00 || Reserved | | 0x00 || Reserved || | ||
|- | |||
| 0x01 || Correction switch top || | |||
|- | |||
| 0x02 || Correction switch bottom || | |||
|- | |- | ||
| | | 0x03 || Relevel switch up || | ||
|- | |- | ||
| | | 0x04 || Relevel switch down || | ||
|- | |- | ||
| | | 0x05 || Impulse up || | ||
|- | |- | ||
| | | 0x06 || Impulse down || | ||
|- | |- | ||
| | | 0x07 || Flush position switch up || | ||
|- | |- | ||
| 0x08 || Flush position switch down || | |||
|- | |- | ||
| | | 0x09 || Pre-end switch top || | ||
|- | |- | ||
| | | 0x0A || Pre-end switch bottom || | ||
|- | |- | ||
| | | 0x0B || Door zone switch A || | ||
|- | |- | ||
| | | 0x0C || Door zone switch B || | ||
|- | |- | ||
|} | |} | ||
Logic table of flush position switches: | |||
{|border="1" cellspacing="" cellpadding="3" | {|border="1" cellspacing="" cellpadding="3" | ||
|- | |- | ||
! | !Flush position switch down | ||
! | !Flush position switch up | ||
! | !State | ||
|- | |- | ||
| | | 0 || 0 || Out of door zone | ||
|- | |- | ||
| | | 0 || 1 || Above flush position inside door zone | ||
|- | |- | ||
| | | 1 || 0 || Below flush position inside door zone | ||
|- | |- | ||
| | | 1 || 1 || Flush position | ||
|- | |- | ||
|} | |} | ||
== Sicherheitskreis (Basic function 0x16, Safety circuit) == | |||
{|border="1" cellspacing="" cellpadding="3" | {|border="1" cellspacing="" cellpadding="3" | ||
|- | |- | ||
! | !Sub-function | ||
! | !Description/Bedeutung | ||
! | !Bemerkung | ||
|- | |- | ||
| | | 0x00 || Reserved || | ||
|- | |- | ||
|} | |} | ||
== Antriebsstatus (Basic function | == Antriebsstatus (Basic function 0x17, Drive unit status) == | ||
{|border="1" cellspacing="" cellpadding="3" | {|border="1" cellspacing="" cellpadding="3" | ||
Zeile 152: | Zeile 129: | ||
| 0x00 || Reserved || | | 0x00 || Reserved || | ||
|- | |- | ||
| 0x01 || Überwachung | | 0x01 || Hauptschütz-Überwachung 1 || | ||
|- | |- | ||
| 0x02 || Überwachung | | 0x02 || Hauptschütz-Überwachung 2 || | ||
|- | |- | ||
| 0x03 || Überwachung | | 0x03 || Bremsschütz-Überwachung || | ||
|- | |- | ||
| 0x04 || | | 0x04 || Bremskontak-Überwachung 1 || | ||
|- | |- | ||
| 0x05 || | | 0x05 || Bremskontak-Überwachung 2 || | ||
|- | |- | ||
| 0x06 || | | 0x06 || Bremskontak-Überwachung 3 || | ||
|- | |- | ||
| 0x07 || | | 0x07 || Temperatur-Vorwarnung || | ||
|- | |- | ||
| 0x08 || | | 0x08 || Übertemperatur || | ||
|- | |- | ||
| 0x09 || | | 0x09 || Bereit (Ready) || | ||
|- | |- | ||
| 0x0A || | | 0x0A || Fehler (Fault) || | ||
|- | |- | ||
| 0x0B || | | 0x0B || Warnung (Alarm) || | ||
|- | |- | ||
| 0x0C || | | 0x0C || Schütze ein (Main contactor) || | ||
|- | |- | ||
| | | 0x0D || Bremse öffnen (Brake) || | ||
|- | |||
| 0x0E || Reserved || | |||
= | |- | ||
| 0x0F || Reserved || | |||
|- | |||
| 0x10 || Reserved || | |||
|- | |||
| 0x11 || Fahrt aufwärts (Moving up) || | |||
|- | |||
| 0x12 || Fahrt abwärts (Moving down) || | |||
|- | |||
| 0x13 || Geschwindigkeit Null (Zero speed) || | |||
|- | |||
| 0x14 || Geschwindigkeit <= 0.3 m/s (Low speed) || | |||
|- | |||
| 0x15 || Geschwindigkeit > 0.3 m/s (High speed) || | |||
|- | |- | ||
| 0x16 || Geschwindigkeit < Übergeschwindigkeit (Speed error low) || | |||
|- | |- | ||
| | | 0x17 || Geschwindigkeit >= Übergeschwindigkeit (Speed error high) || | ||
|- | |- | ||
| | | 0x18 || Reserved || | ||
|- | |- | ||
| | | 0x19 || Überwachung Überdruck || | ||
|- | |- | ||
|} | |} | ||
== Virtueller Türstatus (Basic function | == Virtueller Türstatus (Basic function 0x18, Door unit status) == | ||
Anhand dieser Klemmen generiert das Gerät selbstständig das Statuswort | Anhand dieser Klemmen generiert das Gerät selbstständig das Statuswort des Türsteuergerätes und der Lichtschranke. | ||
des Türsteuergerätes und der Lichtschranke. | |||
{|border="1" cellspacing="" cellpadding="3" | {|border="1" cellspacing="" cellpadding="3" | ||
Zeile 232: | Zeile 217: | ||
== Virtuelle Lastmessung (Basic function | == Virtuelle Lastmessung (Basic function 0x19, Load measuring status) == | ||
Anhand dieser Klemmen generiert das Gerät selbstständig das Statuswort | Anhand dieser Klemmen generiert das Gerät selbstständig das Statuswort der Lastmesseinrichtung. | ||
der | |||
{|border="1" cellspacing="" cellpadding="3" | {|border="1" cellspacing="" cellpadding="3" | ||
Zeile 243: | Zeile 227: | ||
!Bemerkung | !Bemerkung | ||
|- | |- | ||
| 0x00 || Reserved || | | 0x00 || Reserved || Reserviert | ||
|- | |- | ||
| 0x01 || Zero load || Nulllast | | 0x01 || Zero load || Nulllast/Mindestlast | ||
|- | |- | ||
| 0x02 || Normal load || | | 0x02 || Normal load || Normallast | ||
|- | |- | ||
| 0x03 || Full load || Volllast | | 0x03 || Full load || Volllast | ||
Zeile 255: | Zeile 239: | ||
|} | |} | ||
== Diverse Eingänge (Basic function 0x1A, Miscellaneous inputs) == | |||
{|border="1" cellspacing="" cellpadding="3" | {|border="1" cellspacing="" cellpadding="3" | ||
Zeile 269: | Zeile 248: | ||
!Bemerkung | !Bemerkung | ||
|- | |- | ||
| 0x00 || | | 0x00 || Reserved || Reserviert | ||
|- | |- | ||
| 0x01 || | | 0x01 || Überwachung Fahrkorblicht || | ||
|- | |- | ||
| 0x02 || | | 0x02 || Überwachung Triebwerksraumtemperatur || | ||
|- | |- | ||
|} | |} | ||
= Ausgänge = | |||
== Antrieb Geschwindigkeits-Auswahl (Basic function 0x16, Drive unit velocity) == | |||
{|border="1" cellspacing="" cellpadding="3" | {|border="1" cellspacing="" cellpadding="3" | ||
|- | |- | ||
!Sub-function | !Sub-function | ||
!Description | !Description/Bedeutung | ||
!Bemerkung | !Bemerkung | ||
|- | |- | ||
| 0x00 || | | 0x00 || Null-Geschwindigkeit || | ||
|- | |- | ||
| | | 0x01 || Geschwindigkeit 1 || | ||
|- | |- | ||
| ... || ... || | | ... || ... || | ||
|- | |- | ||
| | | 0x07 || Geschwindigkeit 7 || | ||
|- | |- | ||
|} | |} | ||
== | == Antriebssteuerung (Basic function 0x17, Drive unit control) == | ||
{|border="1" cellspacing="" cellpadding="3" | {|border="1" cellspacing="" cellpadding="3" | ||
|- | |- | ||
!Sub-function | !Sub-function | ||
!Description | !Description/Bedeutung | ||
!Bemerkung | !Bemerkung | ||
|- | |- | ||
| 0x00 || Reserved || | | 0x00 || Reserved || | ||
|- | |- | ||
| 0x01 || | | 0x01 || Upwards contactor || Auf-Schütz | ||
|- | |- | ||
| | | 0x02 || Downwards contactor || Ab-Schütz | ||
|- | |- | ||
| 0x03 || Fast contactor || Schnell-Schütz | |||
|- | |- | ||
| | | 0x04 || Slow contactor || Langsam-Schütz | ||
|- | |- | ||
| | | 0x05 || Main contactor || Fahr-Schütz | ||
|- | |- | ||
| | | 0x06 || Brake contactor 1 || Brems-Schütz 1 | ||
|- | |- | ||
| | | 0x07 || Brake contactor 2 || Brems-Schütz 2 | ||
|- | |- | ||
| | | 0x08 || Star/delta contactor || Stern-/Dreieck-Schütz | ||
|- | |- | ||
| | | 0x09 || Enable || Freigabe | ||
|- | |- | ||
| | | 0x0A || Direction up || Richtung auf | ||
|- | |- | ||
| | | 0x0B || Direction down || Richtung ab | ||
|- | |- | ||
| | | ... || ... || ... | ||
|- | |- | ||
| | | 0x11 || V4 || Schnelle Geschwindigkeit | ||
|- | |- | ||
| | | 0x12 || V3 || 1. Zwischen-Geschwindigkeit | ||
|- | |- | ||
| | | 0x13 || V2 || 2. Zwischen-Geschwindigkeit | ||
|- | |- | ||
| | | 0x14 || V1 || 3. Zwischen-Geschwindigkeit | ||
|- | |- | ||
| | | 0x15 || V0 || Langsame Geschwindigkeit (Einfahrgeschwindigkeit) | ||
|- | |- | ||
| | | 0x16 || VN || Nachstellgeschwindigkeit | ||
|- | |- | ||
| | | 0x17 || VI || Inspektionsgeschwindigkeit | ||
|- | |- | ||
| | | 0x18 || Reserved || | ||
|- | |- | ||
| | | 0x19 || Bremspunkt || Direkteinfahrt Verzögern | ||
|- | |- | ||
| | | 0x1A || Korrekturpunkt || Direkteinfahrt Korrektur | ||
|- | |- | ||
|} | |} | ||
== | == Virtuelle Türansteuerung (Basic function 0x18, Door unit control) == | ||
Diese Klemmen generiert das Gerät selbstständig aus dem Steuerwort für das Türsteuergerät. | |||
{|border="1" cellspacing="" cellpadding="3" | {|border="1" cellspacing="" cellpadding="3" | ||
|- | |- | ||
!Sub-function | !Sub-function | ||
!Description | !Description | ||
!Bemerkung | !Bemerkung | ||
|- | |- | ||
| 0x00 || Reserved || | | 0x00 || Reserved || Reserviert | ||
|- | |||
| 0x01 || Door open || Tür öffnen | |||
|- | |- | ||
| | | 0x02 || Door close || Tür schliessen | ||
|- | |- | ||
| | | 0x03 || Door nudging || Drängeln | ||
|- | |- | ||
| | | 0x04 || Door stop || Tür stopp | ||
|- | |- | ||
| | | 0x05 || Door lock || Tür verriegeln | ||
|- | |- | ||
|} | |} | ||
== | == Virtuelle Etagenanzeige binär (Basic function 0x48) == | ||
Diese Klemmen generiert das Gerät selbstständig aus dem Telegramm für den Kabinenstand (Position indicator, basic function 0x40). | |||
{|border="1" cellspacing="" cellpadding="3" | {|border="1" cellspacing="" cellpadding="3" | ||
Zeile 408: | Zeile 370: | ||
!Sub-function | !Sub-function | ||
!Description | !Description | ||
!Bemerkung | !Bemerkung | ||
|- | |- | ||
| 0x00 || | | 0x00 || Position is zero || Aktuelle Etage ist Null (keine Position) | ||
|- | |- | ||
| 0x01 || | | 0x01 || Binary Bit 0 || | ||
|- | |- | ||
| 0x02 || | | 0x02 || Binary Bit 1 || | ||
|- | |- | ||
| | | ... || ... || | ||
|- | |- | ||
| | | 0x08 || Binary Bit 7 || | ||
|- | |- | ||
| | | 0x09 || Position is not zero || Aktuelle Etage ist ungleich Null | ||
|- | |- | ||
| | |} | ||
== Virtuelle Etagenanzeige Gray-Code (Basic function 0x49) == | |||
Diese Klemmen generiert das Gerät selbstständig aus dem Telegramm für den Kabinenstand (Position indicator, basic function 0x40). | |||
{|border="1" cellspacing="" cellpadding="3" | |||
|- | |- | ||
!Sub-function | |||
!Description | |||
!Bemerkung | |||
|- | |- | ||
| | | 0x00 || Position is zero || Aktuelle Etage ist Null (keine Position) | ||
|- | |- | ||
| | | 0x01 || Graycode Bit 0 || | ||
|- | |- | ||
| | | 0x02 || Graycode Bit 1 || | ||
|- | |- | ||
| | | ... || ... || | ||
|- | |- | ||
| | | 0x08 || Graycode Bit 7 || | ||
|- | |- | ||
| | | 0x09 || Position is not zero || Aktuelle Etage ist ungleich Null | ||
|- | |- | ||
|} | |} | ||
[[Kategorie:Erweiterungen des Profils]] | |||
<!-- | |||
== | == Diverse Ausgänge (Basic function 0x4A) == | ||
{|border="1" cellspacing="" cellpadding="3" | {|border="1" cellspacing="" cellpadding="3" | ||
|- | |- | ||
!Sub-function | !Sub-function | ||
!Description | !Description/Bedeutung | ||
!Bemerkung | |||
|- | |- | ||
| 0x00 || | | 0x00 || Reserved || | ||
|- | |- | ||
| 0x01 || | | 0x01 || Außensteuerung ein || | ||
|- | |- | ||
| | | 0x02 || Aufzug in Betrieb || | ||
|- | |- | ||
| | | || Riegel-Relais || | ||
|- | |- | ||
| | | || Aufzug startet || | ||
|- | |- | ||
| | | || Sammelstörung || | ||
|- | |- | ||
| | | || Fahrkorblicht aus || | ||
|- | |- | ||
|} | |} | ||
--> | |||
Aktuelle Version vom 9. September 2015, 10:22 Uhr
Hier erfolgt eine Auflistung von Signalen der virtuellen Ein- und Ausgänge, die als Vorschläge zur Ergänzung des Standards CiA-417 erarbeitet werden.
Eingänge
Inspektionssteuerung (Basic function 0x13, Inspection mode)
Sub-function | Description | Bemerkung |
---|---|---|
0x00 | Reserved | |
0x01 | Inspection on | |
0x02 | Inspection up | |
0x03 | Inspection down | |
0x04 | Inspection fast | |
0x05 | Inspection shaft pit on | |
0x06 | Inspection shaft pit up | |
0x07 | Inspection shaft pit down | |
0x08 | Inspection shaft pit fast |
Rückholsteuerung (Basic function 0x14, Emergency recall operation)
Sub-function | Description | Bemerkung |
---|---|---|
0x00 | Reserved | |
0x01 | Emergency recall operation on | |
0x02 | Emergency recall operation up | |
0x03 | Emergency recall operation down |
Kopierwerk/Magnetschalter (Basic function 0x15, Shaft copy)
Sub-function | Description | Bemerkung |
---|---|---|
0x00 | Reserved | |
0x01 | Correction switch top | |
0x02 | Correction switch bottom | |
0x03 | Relevel switch up | |
0x04 | Relevel switch down | |
0x05 | Impulse up | |
0x06 | Impulse down | |
0x07 | Flush position switch up | |
0x08 | Flush position switch down | |
0x09 | Pre-end switch top | |
0x0A | Pre-end switch bottom | |
0x0B | Door zone switch A | |
0x0C | Door zone switch B |
Logic table of flush position switches:
Flush position switch down | Flush position switch up | State |
---|---|---|
0 | 0 | Out of door zone |
0 | 1 | Above flush position inside door zone |
1 | 0 | Below flush position inside door zone |
1 | 1 | Flush position |
Sicherheitskreis (Basic function 0x16, Safety circuit)
Sub-function | Description/Bedeutung | Bemerkung |
---|---|---|
0x00 | Reserved |
Antriebsstatus (Basic function 0x17, Drive unit status)
Sub-function | Description/Bedeutung | Bemerkung |
---|---|---|
0x00 | Reserved | |
0x01 | Hauptschütz-Überwachung 1 | |
0x02 | Hauptschütz-Überwachung 2 | |
0x03 | Bremsschütz-Überwachung | |
0x04 | Bremskontak-Überwachung 1 | |
0x05 | Bremskontak-Überwachung 2 | |
0x06 | Bremskontak-Überwachung 3 | |
0x07 | Temperatur-Vorwarnung | |
0x08 | Übertemperatur | |
0x09 | Bereit (Ready) | |
0x0A | Fehler (Fault) | |
0x0B | Warnung (Alarm) | |
0x0C | Schütze ein (Main contactor) | |
0x0D | Bremse öffnen (Brake) | |
0x0E | Reserved | |
0x0F | Reserved | |
0x10 | Reserved | |
0x11 | Fahrt aufwärts (Moving up) | |
0x12 | Fahrt abwärts (Moving down) | |
0x13 | Geschwindigkeit Null (Zero speed) | |
0x14 | Geschwindigkeit <= 0.3 m/s (Low speed) | |
0x15 | Geschwindigkeit > 0.3 m/s (High speed) | |
0x16 | Geschwindigkeit < Übergeschwindigkeit (Speed error low) | |
0x17 | Geschwindigkeit >= Übergeschwindigkeit (Speed error high) | |
0x18 | Reserved | |
0x19 | Überwachung Überdruck |
Virtueller Türstatus (Basic function 0x18, Door unit status)
Anhand dieser Klemmen generiert das Gerät selbstständig das Statuswort des Türsteuergerätes und der Lichtschranke.
Sub-function | Description | Bemerkung |
---|---|---|
0x00 | Reserved | |
0x01 | Door open switch | Endschalter auf |
0x02 | Door close switch | Endschalter zu |
0x03 | Error | Türstörung |
0x04 | Force limit | Tür Blockiert |
0x05 | Finger protector | Einzugschutz |
0x06 | Motion detector | Vorraumüberwachung |
0x07 | Reserved | |
... | ... | |
0x10 | Reserved | |
0x11 | Light barrier | Lichtschranke |
Virtuelle Lastmessung (Basic function 0x19, Load measuring status)
Anhand dieser Klemmen generiert das Gerät selbstständig das Statuswort der Lastmesseinrichtung.
Sub-function | Description | Bemerkung |
---|---|---|
0x00 | Reserved | Reserviert |
0x01 | Zero load | Nulllast/Mindestlast |
0x02 | Normal load | Normallast |
0x03 | Full load | Volllast |
0x04 | Overload | Überlast |
Diverse Eingänge (Basic function 0x1A, Miscellaneous inputs)
Sub-function | Description | Bemerkung |
---|---|---|
0x00 | Reserved | Reserviert |
0x01 | Überwachung Fahrkorblicht | |
0x02 | Überwachung Triebwerksraumtemperatur |
Ausgänge
Antrieb Geschwindigkeits-Auswahl (Basic function 0x16, Drive unit velocity)
Sub-function | Description/Bedeutung | Bemerkung |
---|---|---|
0x00 | Null-Geschwindigkeit | |
0x01 | Geschwindigkeit 1 | |
... | ... | |
0x07 | Geschwindigkeit 7 |
Antriebssteuerung (Basic function 0x17, Drive unit control)
Sub-function | Description/Bedeutung | Bemerkung |
---|---|---|
0x00 | Reserved | |
0x01 | Upwards contactor | Auf-Schütz |
0x02 | Downwards contactor | Ab-Schütz |
0x03 | Fast contactor | Schnell-Schütz |
0x04 | Slow contactor | Langsam-Schütz |
0x05 | Main contactor | Fahr-Schütz |
0x06 | Brake contactor 1 | Brems-Schütz 1 |
0x07 | Brake contactor 2 | Brems-Schütz 2 |
0x08 | Star/delta contactor | Stern-/Dreieck-Schütz |
0x09 | Enable | Freigabe |
0x0A | Direction up | Richtung auf |
0x0B | Direction down | Richtung ab |
... | ... | ... |
0x11 | V4 | Schnelle Geschwindigkeit |
0x12 | V3 | 1. Zwischen-Geschwindigkeit |
0x13 | V2 | 2. Zwischen-Geschwindigkeit |
0x14 | V1 | 3. Zwischen-Geschwindigkeit |
0x15 | V0 | Langsame Geschwindigkeit (Einfahrgeschwindigkeit) |
0x16 | VN | Nachstellgeschwindigkeit |
0x17 | VI | Inspektionsgeschwindigkeit |
0x18 | Reserved | |
0x19 | Bremspunkt | Direkteinfahrt Verzögern |
0x1A | Korrekturpunkt | Direkteinfahrt Korrektur |
Virtuelle Türansteuerung (Basic function 0x18, Door unit control)
Diese Klemmen generiert das Gerät selbstständig aus dem Steuerwort für das Türsteuergerät.
Sub-function | Description | Bemerkung |
---|---|---|
0x00 | Reserved | Reserviert |
0x01 | Door open | Tür öffnen |
0x02 | Door close | Tür schliessen |
0x03 | Door nudging | Drängeln |
0x04 | Door stop | Tür stopp |
0x05 | Door lock | Tür verriegeln |
Virtuelle Etagenanzeige binär (Basic function 0x48)
Diese Klemmen generiert das Gerät selbstständig aus dem Telegramm für den Kabinenstand (Position indicator, basic function 0x40).
Sub-function | Description | Bemerkung |
---|---|---|
0x00 | Position is zero | Aktuelle Etage ist Null (keine Position) |
0x01 | Binary Bit 0 | |
0x02 | Binary Bit 1 | |
... | ... | |
0x08 | Binary Bit 7 | |
0x09 | Position is not zero | Aktuelle Etage ist ungleich Null |
Virtuelle Etagenanzeige Gray-Code (Basic function 0x49)
Diese Klemmen generiert das Gerät selbstständig aus dem Telegramm für den Kabinenstand (Position indicator, basic function 0x40).
Sub-function | Description | Bemerkung |
---|---|---|
0x00 | Position is zero | Aktuelle Etage ist Null (keine Position) |
0x01 | Graycode Bit 0 | |
0x02 | Graycode Bit 1 | |
... | ... | |
0x08 | Graycode Bit 7 | |
0x09 | Position is not zero | Aktuelle Etage ist ungleich Null |